Home > Shop By Car Make > Dodge >

56021903 AA OEM 3 Button Key Fob
56021903 AA Factory OEM KEY FOB Keyless Entry Remote Alarm Clicker Replacement
 
Dealer Price $89.95
Our Price: $14.77
Savings: $75.18
Part Numbers: 56021903AA | FCC ID: GQ43VT7T
Interchangeable Part Numbers:4686076 | 04686366 | 56008761 | 56008762
Battery Size: CR2016 x2 (sold separately)

Quantity in Stock:343

Product Code:
56021903AA
Qty:

  
Description Specs & Vehicle Compatibility Before You Purchase
 
Details:
This is a Factory OEM (Original Equipment Manufacturer) 3 button keyless entry remote, aka "key fob" for Chrysler, Dodge, and Jeep.
These are genuine Chrysler, Dodge, Jeep OEM electronics.
You will receive one of the listed interchangeable part numbers.

Programming Instructions:
NOTICE: YOU MUST HAVE A WORKING REMOTE FOR PROCEDURE 1 AND 2 TO WORK. IF YOU DON'T HAVE A WORKING REMOTE THEN YOU MUST HAVE YOUR REMOTE PROGRAMMED BY A DEALER OR LOCKSMITH USING DIAGNOSTIC EQUIPMENT.

*PLEASE READ ENTIRE PROCEDURE BEFORE PERFORMING. SOME VEHICLES MAY USE ONE OF THREE PROCEDURES.

NOTE: DURANGOS, DAKOTAS, RAMS, AND CHEROKEES MUST BE PROGRAMMED BY A DEALERSHIP OR LOCKSMITH USING DIAGNOSTIC EQUIPMENT.

Programming procedure #1

Obtain all remote transmitters for this vehicle.

1. Put key in ignition and turn ignition switch to ON position (as far as you can turn key without cranking engine).

2. Press and hold UNLOCK on a currently functioning remote for 4 to 10 seconds.

3. While holding the UNLOCK button during the 4 to 10 second period, press the panic button for one second and release both buttons at the same time. A chime should sound within three seconds to indicate the vehicle has entered programming mode.

4. Press any button on the remote used in step 3. You should hear an audible tone indicating that remote has been re-programmed. This step must be done within 30 seconds of hearing first chime in step 3.

5. Within 30 seconds of completing step 4, press any button on the next remote. Repeat step 5 for all additional remotes including working remotes.

6. Programming is now complete. Turn ignition off and test remotes to ensure proper programming.

Programming Procedure #2

Obtain all remote transmitters for this vehicle.

1. Put key in ignition and turn ignition switch to ON position (as far as you can turn key without cranking engine).

2. Press and hold UNLOCK on a currently functioning remote for 4 to 10 seconds.

3. While holding the UNLOCK button during the 4 to 10 second period, press the panic button for one second and release both buttons at the same time. A chime should sound within three seconds to indicate the vehicle has entered programming mode.

4. Press the LOCK and UNLOCK buttons simultaneously on the same remote used in step 3. then release. You should hear an audible tone indicating that the remote was recognized. Once tone is heard press and release the UNLOCK button on that remote. A chime should sound indicating that the remote has been programmed. This must be done within 30 seconds of step 3.

5. Within 30 seconds of completing step 4, press the LOCK and UNLOCK button on the next remote then release. You should hear an audible tone indicating that the remote was recognized. Once tone is heard press and release the UNLOCK button on that remote. A chime should sound indicating that the remote has been programmed. Repeat step 5 for all additional remotes including working remotes.

6. Programming is now complete. Turn ignition off and test remotes to ensure proper programming.

Programming Procedure #3 (Plymouth Neon)

Obtain all remote transmitters for this vehicle.

1. Identify the programming connector. It will be on the driver’s side under the dash taped to the wiring harness just to the left of the steering column. It will be a single green wire with a black rubber insulator on the end of it.

2. Using a suitable jumper wire jump the programming connector to ground. This means contact the metal in the connector with one end of the wire and contact a non-painted metal surface with the other end of the wire.

3. Insert key into the ignition and turn the ignition switch to the ON position. (Just shy of cranking the engine)

4. Press any button on the first remote. The locks will cycle from Lock to Unlock to show successful programming. Repeat this step for each additional remote to be programmed.

5. Remove jumper wire, turn ignition to OFF and remove key. Test all remotes to ensure they function.





56021903AA | FCC ID: GQ43VT7T


Accessories
Lemon Lime Air Freshener Sonic Key Finder 12" Ice Scraper Bluetooth Audio Adapter
Our Price: $1.99
Our Price: $6.95
Our Price: $7.95
Our Price: $14.95
Lemon Lime Air Freshener Sonic Key Finder 12" Ice Scraper

Average Rating: 4.5 of 5 Total Reviews: 3 Write a review »

  0 of 0 people found the following review helpful:
 
Great product August 10, 2016
Reviewer: jordan ashburn from livingston, TN United States  
I received my remote for my 97 ram 3500 and it works great. Super easy to program thanks!

Was this review helpful to you?

  0 of 0 people found the following review helpful:
 
very fast August 31, 2015
Reviewer: GOKHAN ILHAN from ANKARA, ANKARA Turkey  
I took the products very fast,  I did not use them but goods look nice...

Was this review helpful to you?

  0 of 0 people found the following review helpful:
 
KEY FOB Keyless Entry Remote November 12, 2014
Reviewer: Joseph Strauch from Glen Mills, PA United States  
Timely and as expected.

Was this review helpful to you?




We're here for you from purchase to programming!
Unmatched, expert support for ANY keyless remote issue.
We've got your back.

Become a Preferred Business Partner?
Are you a car dealer? Locksmith? Become a Preferred Partner for preferred pricing, dedicated support reps, & more.