Home > Shop By Car Make > Mitsubishi >

OUCG8D-525M-A Mitsubishi OEM 3 Button Key Fob
MITSUBISHI OUCG8D-525M-A Factory OEM KEY FOB Keyless Entry Remote Alarm Replace
 
Dealer Price $129.95
Our Price: $35.77
Savings: $94.18
Part Numbers: OUCG8D525MA_BLACKPANIC | G8D-525M-A | FCC ID OUCG8D-525M-A | | 3BUTTONS | BLACK PANIC BUTTON |
Battery Size: CR2032 (sold separately)

Quantity in Stock:(Out of Stock)

Product Code:
OUCG8D525MA_BLACKPANIC
Qty:

  
Description Specs & Vehicle Compatibility Before You Purchase
 

Details:
This is a Factory OEM (Original Equipment Manufacturer) 3 button keyless entry remote, aka "key fob" for Mitsubishi. See "Compatibility Tab" for a full list of compatible vehicles.
These are genuine OEM electronics in a new aftermarket case.

All models 06' and up require professional programming by the dealer or an automotive locksmith.

Programming Instructions:
dlc-port-1-16.jpg
Diagram of Data Link Connector (DLC)

Programming Procedure for Diamante, Endeavor, Galant, Montero, Eclipse, Lancer, and Outlander

Obtain all remote transmitters for this vehicle. This procedure's a little more complicated than others, we recommend having someone help you perform this procedure.

1. Locate the Data Link Connector (DLC). It will be in the trunk or under the dash on the drivers side. You may need to lay on the floor and look up to easily access it. Use the diagram above to identify ports 1 and 4. Notice that the DLC connector is tapered. You can use this to help identify the proper ports. Be sure there's metal contact pins in ports 1 and 4.

2. Insert key into the ignition and leave in the OFF position.

3. Using a suitable jumper wire, jump pin 1 to pin 4. Jump means to make a connection between the two pins using any metal wire. A paperclip bent in the shape of a "U" usually works perfect. Be certain the jumper wire makes contact with the pins in ports 1 and 4. Once the jumper wire is installed it needs to remain there throughout this procedure until instructed to remove.

4. Within ten seconds of connecting the jumper wire, press the hazard light switch 6 times. The doors will automatically lock and unlock once indicating the vehicle is in programming mode.

5. Now press the LOCK button on the first remote to be programmed THREE TIMES within ten seconds. The doors will automatically lock and unlock once indicating the vehicle has programmed that remote.

6. If you have additional remotes to program, repeat step 5 within one minute.

7. Once all remotes are programmed remove jumper. Test all remotes to ensure proper programming.

Programming Procedure for 00-05 Montero Sport

Obtain all remote transmitters for this vehicle. This procedure's a little more complicated than others, we recommend having someone help you perform this procedure.

1. Locate the Data Link Connector (DLC). It will be under the dash on the drivers side. You may need to lay on the floor and look up to easily access it. Use the diagram above to identify ports 1 and 4. Notice that the DLC connector is tapered. You can use this to help identify the proper ports. Be sure there's metal contact pins in ports 1 and 4.

2. Insert key into the ignition and leave in the OFF position.

3. Using a suitable jumper wire, jump pin 1 to pin 4. Jump means to make a connection between the two pins using any metal wire. A paperclip bent in the shape of a "U" usually works perfect. Be certain the jumper wire makes contact with the pins in ports 1 and 4. Once the jumper wire is installed it needs to remain there throughout this procedure until instructed to remove.

4. Within ten seconds of connecting the jumper wire, turn the ignition switch to ACC (switch to ON position for some ’00 models) then back to OFF, THREE times*. You must do this step very quickly; all three cycles should take 2-3 seconds. (ON is the position just shy of cranking the engine; ACC is the position when you turn the key back towards yourself; OFF is the position where you can remove your key). The doors will automatically lock and unlock once indicating the vehicle is in programming mode.

5. Now press the LOCK button on the first remote to be programmed THREE TIMES within ten seconds. The doors will automatically lock and unlock once indicating the vehicle has programmed that remote.

6. If you have additional remotes to program, repeat step 5 within one minute.

7. Once all remotes are programmed remove jumper. Test all remotes to ensure proper programming.

* If you are getting no response from turning the ignition from ON to OFF, Then try the step turning the ignition from OFF to ACC. The ‘00 Montero sport was the first vehicle with this procedure and it was changed for the ‘01 model year from ON to OFF, to ON to ACC.




OUCG8D525MA_BLACKPANIC | G8D-525M-A | FCC ID OUCG8D-525M-A | | 3BUTTONS | BLACK PANIC BUTTON |

Accessories
12" Ice Scraper Lemon Lime Air Freshener Bluetooth Audio Adapter Sonic Key Finder
Our Price: $7.95
Our Price: $1.99
Our Price: $14.95
Our Price: $6.95
12" Ice Scraper Lemon Lime Air Freshener Sonic Key Finder

Share Your Knowledge of this Product. Be the first to write a review »



We're here for you from purchase to programming!
Unmatched, expert support for ANY keyless remote issue.
We've got your back.

Become a Preferred Business Partner?
Are you a car dealer? Locksmith? Become a Preferred Partner for preferred pricing, dedicated support reps, & more.