Home > Shop By Car Make > Chevrolet >

25668603 OEM Key Fob Circuit Board with New Remote Case
25668603 Factory 4 BUTTON OEM KEY FOB Keyless Entry Car Remote Alarm Replace
 
Dealer Price $119.99
Our Price: $25.77
Savings: $94.22
FCCID: KOBUT1BT | KOBUTIBT
Part Number: 25668603
Interchange Part Number: 1983 101 393
Battery Size: CR2032 (sold separately)

Quantity in Stock:73

Product Code:
25668603
Qty:

Description Specs & Vehicle Compatibility Before You Purchase
 

Details:
This is a Factory OEM (Original Equipment Manufacturer) 4 button keyless entry remote, aka "key fob" for Buick, Chevrolet, Oldsmobile, and Pontiac. See "Compatibility Tab" for a full list of compatible vehicles.
These are genuine OEM electronics in a new aftermarket case.

Programming Instructions:

(There are 2 possible programming Procedures)

NOTE: 2OOO Buick LeSabre, I999 Oldsmobile Alero & I999 Pontiac Grand Am - Must be programmed by a professional.

*You must have all remotes, including working ones, when performing this procedure.


Procedure #1:

1. Close all doors.

2. Turn ignition to ON then back to OFF (ON is the position just shy of starting car without cranking the engine.)

3. Remove key from ignition.

4. Press and hold the UNLOCK switch on the driver's door and continue to hold until instructed to release.

5. Insert key into the ignition (do not turn it) and remove it.

6. Insert key into the ignition (do not turn it) and remove it.

7. Insert key into the ignition (do not turn it) and leave it in.

8. Release the UNLOCK switch on driver's door. Vehicle will respond with three acoustic sounds to indicate successful entry into programming mode.

9. Press and hold the LOCK and UNLOCK buttons on the first remote until vehicle beeps twice indicating successful programming. This step may take about 15 seconds.

10. Repeat step 9 for all remaining remotes, including working ones.

11. Remove key from ignition to exit programming mode and test all remotes.


Procedure #2:

1. Locate the Data Link Port. It is located under the driver's side dash. Notice the port is wider on the top row. Be sure there are metal pins inside ports 4 and 8. Refer to diagram to locate the proper pins.

2. Connect pin 4 to pin 8 with a suitable jumper wire. Any short piece of wire will work. A paper clip in the shape of a U works well. (Leave jumper wire connected throughout the programming procedure.

3. Insert key into the ignition and turn the ignition cylinder to the ON position. The vehicle will respond by locking and unlocking the doors to indicate the vehicle has entered programming mode.

4. Press and hold both the Lock and UNLOCK buttons together on the first remote to be programmed. After about 15 seconds, the vehicle will respond by locking and unlocking the doors. Release the buttons on the remote.

5. Within one minute, repeat step 4 for all additional remotes, including previously working ones.

6. Remove the jumper wire connected to the Data Link Port.



25668603 | | FCC ID: KOBUT1BT | GM / UTA 25668603 | 4 BUTTON | CANADA: 1983 101 393

Part Number / FCC ID / Canada
  • 25668603

    FCC ID: KOBUT1BT
    GM / UTA 25668603
    4 BUTTON
    CANADA: 1983 101 393

Accessories
Bluetooth Audio Adapter 12" Ice Scraper Lemon Lime Air Freshener Sonic Key Finder
Our Price: $14.95
Our Price: $7.95
Our Price: $1.99
Our Price: $6.95
12" Ice Scraper Lemon Lime Air Freshener Sonic Key Finder

Share Your Knowledge of this Product. Be the first to write a review »


We Are the Key Fob Experts
Unmatched, expert support for ANY keyless remote issue.
We've got your back.

Key Fob Programming Instructions
Key Fob & Transponder Key Programming Instructions for over 5,000 vehicles!