1995 Infiniti J30 Key Fob Remote Programming Instructions

Here are the programming instructions for a 1995 Infiniti J30 Key Fob Remote. Don't forget to check our store if you need an extra Key Fob or Replacement Fob for any vehicle you might have. Keylessentryremotefob.com

ORDER THIS KEY FOB PART NUMBER HERE: A269ZJA073




To reprogram (enter new ID) key fob (keyless remote controller) follow the steps.

1. Close all doors and lock all doors

2. Insert and remove the key from the ignition key cylinder more than six times
within 10 seconds. The hazard-warning lamp will then flash. NOTE: Key should be withdrawn from ignition key cylinder completely each time. NOTE: Do Not rush the insertion/removal key cycling process. The side marker/tail/license lamps and interior illumination will flash twice when this step
is accurately completed.

3. Insert key on ignition key cylinder and turn ignition key switch to "AAC"
position. At this time, the new ID code is entered and original (previous) ID
codes are erased.

4. Press any button on the new remote controller once. (The hazard warning
lamp will then flash) NOTE: Do Not press the button more than one time in the above step. If the button is pressed more than one time, the programming procedure will not be
successful. The side marker/tail/license lamps and interior illumination will
flash twice when this step is accurately completed and programming is
successful. If there is only one remote controller skip step 5.

5. Additional ID code entry: Release the door lock, then lock again with door lock/unlock switch (In power window main switch)

6. Remove key from ignition

7. Unlock driver side door, open driver side door and then close the door.
(END) NOTE: If you need to activate more than two additional new remote controllers, repeat the procedure on step 5 "Additional ID code entry" for each new remote
controller.

NOTE: Entry of maximum four ID codes is allowed and any attempt to enter more will
be ignored.


FOB Programming Instructions 2

Enter the identity (ID) code manually when: remote controller or multi-remote control unit LCU05 is replaced. an additional remote controller is activated. ID Code Entry Procedure To enter the ID code, follow this procedure. Entering "Setting mode":

(1) Close and lock all doors.

 (2) Insert and remove the key from the ignition more than six times within 10 seconds. (The hazard-warning lamp will then flash twice.) At this time, the original ID codes are eliminated. ID code entry:

(3) Turn ignition key to "ACC" position.

(4) Push lock button on the new remote controller once (for example, if door is locked using the remote controller during this ID code entry enable state, a new ID code can be entered). At this time, the new ID code is entered. (The hazard-warning lamp will then flash twice.) Additional ID code entry

(5) If you need to activate additional remote controllers, unlock the driver's door, then lock again with door lock knob.

(6) Push lock button on the additional new remote controller once.

(7) This ID code entry enable state and setting mode remain until the driver's door is opened. NOTE If you need to activate more than two additional new remote controllers, repeat the procedure "Additional ID code entry" for each new remote controller. If the same ID code that exists in the memory is input, the hazard warning lamps will flash twice but the entry will be ignored. Entry of maximum four ID codes is allowed and any attempt to enter more will be ignored. Any ID codes entered after termination of the "setting mode" will not be accepted. Additionally remote control signals will be inhibited when an ID code has not been entered during the "setting" mode.


FOB Programming Instructions 3
To reprogram (enter new ID) key fob (keyless remote controller) follow the steps.

1. Close all doors and lock all doors

2. From the door switch unlock the trunk.

3. Insert and remove the key from the ignition key cylinder six times within 10 seconds. NOTE: Key should be withdrawn from ignition key cylinder completely each time.
NOTE: Do not rush the insertion/removal key cycling process. The side marker/tail/license lamps and interior illumination will flash twice when this step is accurately completed.
NOTE: At this time, the new ID code is entered and original (previous) ID codes are erased.

4. Manually unlock and lock the driver side door

5. Push any button on the new remote controller once.
If there is only one remote controller skip step 6.

6. Additional ID code entry Repeat step 4 and 5

7. END.


Was This Information Useful?  Please take a moment to Like / Follow us and share via social media below. It is people like you that help spread the word about us.  It helps so much!  Thanks for visiting and sharing with your friends and family!