Keyless Entry Remote
close
close
Limited Time Offer! 15% Off Any 2 or More Key Fobs

1993 Jeep Grand Cherokee Key Fob Remote Programming Instructions

Posted by Keyless Entry Remote on Apr 15th 2013


Here are the programming instructions for a 1993 Jeep Grand Cherokee Key Fob Remote. If you need an extra Key Fob or Replacement Fob for any vehicle you might have visit us at Keylessentryremotefob.com You can also leave comments or suggestions at the bottom of this blog and if you like what we provide please forward on to your friends & family; people like you are our best advertising tool!

ORDER THIS KEY FOB PART NUMBER HERE: 56009031




PLEASE NOTE:  When you begin the programming sequence to sync your remote to your installed remote keyless entry (RKE) system, you MUST HAVE ALL OF YOUR REMOTES (Including PREVIOUSLY PROGRAMMED remote(s)) to be programmed with you at the time of programming…

ALL PREVIOUSLY PROGRAMMED REMOTES WILL BE ERASED AT THIS TIME.

(This is a safety feature which prevents anyone else from accessing your vehicle.)

 UP TO 4 REMOTES (total) may be programmed to your vehicle’s system at one time.

KEYLESS REMOTE PROGRAMMING PROCEDURE:

METHOD #1:

Programming Dual Button Transmitters To Vehicle


Up to 4 transmitters can be programmed into the receiver at any given time.

All transmitters to be used on a vehicle must be programmed during this procedure.

(1) Open the driver’s door and leave it open during the programming process.

 (2) Move the mechanical door lock lever on the driver’s door to the LOCK position.

 (3) Insert the ignition key and turn it to the RUN position. (Do not start the vehicle.)

 (4) After turning the ignition key to the Run position aim the transmitter at the receiver and press the LOCK (right) button for 5 seconds. Once the receiver accepts the programming the door will unlock.

 (5) If additional transmitters are to be used on the vehicle each must be programmed during the programming sequence. (Up to 4 transmitters can be programmed to a vehicle) To program additional transmitters: Return the mechanical door lock lever on the driver’s door to the LOCK position and aim the next transmitter at the receiver and press the UNLOCK (left) button for 5 seconds.  (Press the LOCK (right) button for 5 seconds IF UNLOCK DOES NOT SEEM TO DO IT) Again when the receiver accepts the programming the door will unlock. Repeat step 5 until all transmitters have been programmed.

 (6) When all transmitters have been programmed to the receiver, the ignition must be turned off and back on within 20 seconds after programming the last transmitter. When this is done, only the transmitters that were programmed to the vehicle during this procedure will operate the locks.

METHOD #2:

Up to 4 transmitters can be programmed into the receiver at any given time.

All transmitters to be used on a vehicle must be programmed during this procedure.

(1) Open the driver’s door and leave it open during the programming process.

 (2) Move the mechanical door lock lever on the driver’s door to the LOCK position.

 (3) Insert the ignition key and turn it to the RUN position. (Do not start the vehicle.)

 (4) After turning the ignition key to the Run position aim the transmitter at the receiver and press the LOCK (right) button for 5 seconds. Once the receiver accepts the programming the door will unlock.

Move to Step 5 If you have more than one transmitter you are going to use with this vehicle. Move to Step 6 If only one Jeep remote is used.

 (5) If additional transmitters are to be used on the vehicle each must be programmed during the programming sequence. (Up to 4 transmitters can be programmed to a vehicle) To program additional transmitters: Return the mechanical door lock lever on the driver’s door to the LOCK position and aim the next transmitter at the receiver and press the UNLOCK (left) button for 5 seconds. Again when the receiver accepts the programming the door will unlock. Repeat step 5 until all transmitters have been programmed.

 (6) When all transmitters have been programmed to the receiver, the ignition must be turned off and back on within 20 seconds after programming the last transmitter. When this is done, only the transmitters that were programmed to the vehicle during this procedure will operate the locks.


Was This Information Useful?  Please take a moment to Like / Follow us and share via social media below. It is people like you that help spread the word about us.  It helps so much!  Thanks for visiting and sharing with your friends and family!


Subscribe To Our Social Networks For Special Discounts, Offers, & Contests!

        
By Keyless Entry Remote Inc

We Are The Experts

Unmatched, expert support for ANY keyless remote issue. We've got your back!

Need Help?

Stay In The Know

Sign up for Keyless Entry Remote's News, Sales, and Deals.

Join Our Mailing List

Programming Instructions

Remote & Transponder Key Programming Instructions for over 5,000 vehicles!

Find Yours