null
close
close
*Exclusions
Apply

1997 Cadillac Eldorado Key Fob Remote Programming Instructions

Posted by Keyless Entry Remote on Apr 2nd 2013


Here are the programming instructions for a 1997 Cadillac Eldorado Key Fob Remote. If you need an extra Key Fob or Replacement Fob for any vehicle you might have visit us at Keylessentryremotefob.com You can also leave comments or suggestions at the bottom of this blog and if you like what we provide please forward on to your friends & family; people like you are our best advertising tool!

ORDER THIS KEY FOB PART NUMBER HERE: 16259819



   Use these instructions if your Deville has an  Analog Instrument Cluster

1.   Press OFF and WARM buttons on  Climate Control Panel (CCP) simultaneously.
      (Instrument Panel Cluster (IPC) will light all telltales, then go blank) System is now in diagnostic mode.
       Press PASSENGER COOLER button until “RFA” is displayed, then press FAN UP.
      If   “RFA DATA” is displayed, press FAN DOWN.
      If   “RFA OVERRIDE” is displayed, press FAN UP.

2.   If  â€œRFA 500 NO OVERRIDE” is displayed, press FAN DOWN.
      If  â€œRFA 501 PROGRAM FOB #1” is displayed, Press FAN UP.

3.   IPC will show “0” on right side of Driver Information Center (DIC) display.
      Press warmer button on climate control unit until “99” is displayed.

4.   Press and hold TRUNK button on transmitter. While holding TRUNK button, press LOCK button and hold for one
      second. Hold both buttons for a total of 3 seconds. Locks cycle when programming is complete (if remote is not
      programmed within 30 seconds after entering “99” override display, system will default and you must begin again at
      step 2.

5.   To program a second remote, press FAN DOWN button until  â€œRFA 502 PROGRAM FOB #2” is displayed, then press
      FAN UP.  Repeat step 4.

      To exit system, press AUTO, MODE UP, MODE DOWN, or RESET.

       Use these instructions if your DeVille has a  Digital Instrument Cluster

1.   Press OFF and WARM buttons on Climate Control Center (CCC) simultaneously. Instrument Panel Cluster (IPC) will
       light all telltales, go blank then  enter DIAGNOSTIC MODE. Press FAN DOW button to scroll through system until
       â€œRFA” is displayed, then press FAN UP button. Press FAN DOWN button until “RFA OVERRIDE” is displayed, then
        press FAN UP button. When  â€œNO OVRD RF 500” is displayed, then press FAN UP button.

2.   When “PGM FOBL 501” is displayed, press WARM button and “99” will be displayed in left upper corner of IPC just
      below odometer. System is now ready to program remote.

3.   Press and hold TRUNK button on transmitter. While holding TRUNK button, press LOCK button and hold for one
      second. Hold both buttons for a total of 3 seconds. Locks cycle when programming is complete (if remote is not
      programmed within 30 seconds after entering “99” override display, system will default and you must begin again at
      step 2.)

4.  To program second remote, pres FAN UP button until “PGM FOB2 502” is displayed, then follow steps 2 and 3 to
      program second remote.

     To exit system, press RECIRC or RESET buttons.


Was This Information Useful?  Please take a moment to Like / Follow us and share via social media below. It is people like you that help spread the word about us.  It helps so much!  Thanks for visiting and sharing with your friends and family!


Subscribe To Our Social Networks For Special Discounts, Offers, & Contests!

        
By Keyless Entry Remote Inc

We Are The Experts

Unmatched, expert support for ANY keyless remote issue. We've got your back!

Need Help?

Stay In The Know

Sign up for Keyless Entry Remote's News, Sales, and Deals.

Join Our Mailing List

Programming Instructions

Remote & Transponder Key Programming Instructions for over 5,000 vehicles!

Find Yours