1996 Cadillac Seville Key Fob Remote Programming Instructions

Here are the programming instructions for a 1996 Cadillac Seville Key Fob Remote. If you need an extra Key Fob or Replacement Fob for any vehicle you might have visit us at Keylessentryremotefob.com You can also leave comments or suggestions at the bottom of this blog and if you like what we provide please forward on to your friends & family; people like you are our best advertising tool!

ORDER THIS KEY FOB PART NUMBER HERE: 16259819



PLEASE NOTE:  When you begin the programming sequence to sync your remote to your installed remote keyless entry (RKE) system, you MUST HAVE ALL OF YOUR REMOTES (Including PREVIOUSLY PROGRAMMED remote(s)) to be programmed with you at the time of programming…

ALL PREVIOUSLY PROGRAMMED REMOTES WILL BE ERASED AT THIS TIME.

(This is a safety feature which prevents anyone else from accessing your vehicle.)

 UP TO 4 REMOTES (total) may be programmed to your vehicle’s system at one time.

KEYLESS REMOTE PROGRAMMING PROCEDURE:

AT TIME OF PROGRAMMING:

 ALL remotes to be programmed and/or reprogrammed MUST BE PRESENT.

METHOD #1:  

Use these instuctions if your Deville  has an  Analog Instrument Cluster

1.   Press  OFF and WARM buttons on  Climate Control Panel (CCP)  simultaneously.
(Instrument Panel  Cluster (IPC) will light all telltales, then go blank) System is now in  diagnostic mode.  Press PASSENGER COOLER button until “RFA” is  displayed, then press FAN UP.

      If   “RFA DATA” is displayed,  press FAN DOWN.

       If   “RFA OVERRIDE” is displayed, press FAN UP.

2.   If   “RFA 500 NO OVERRIDE” is displayed, press FAN DOWN.

      If   “RFA 501 PROGRAM FOB #1” is displayed, Press FAN UP.

3.   IPC  will show “0” on right side of Driver Information Center (DIC) display. Press  warmer button on climate control unit until “99” is displayed.

4.   Press  and hold TRUNK button on transmitter. While holding TRUNK button, press  LOCK button and hold for one second. Hold both buttons for a  total of 3 seconds. Locks cycle when programming is complete (if remote  is not programmed within 30 seconds after entering “99”  override display, system will default and you must begin again at step 2.

5.   To program a second remote, press  FAN DOWN button until  â€œRFA 502 PROGRAM FOB #2” is  displayed, then press  FAN UP.  Repeat step 4.

To exit  system, press AUTO, MODE UP, MODE DOWN, or RESET.


METHOD #2: 

Use these instructions if your DeVille has a  Digital  Instrument Cluster


1.   Press  OFF and WARM buttons on Climate Control Center (CCC) simultaneously.  Instrument Panel Cluster (IPC) will light all telltales, go  blank then  enter DIAGNOSTIC MODE. Press FAN DOW button to scroll  through system until “RFA” is displayed, then press FAN UP  button. Press FAN DOWN button until “RFA OVERRIDE” is displayed, then press FAN UP button. When  â€œNO OVRD RF 500” is displayed,  then press FAN UP button.

2.   When “PGM FOBL 501” is  displayed, press WARM button and “99” will be displayed in left upper  corner of IPC just below odometer. System is now ready to  program remote.

3.   Press and hold TRUNK button on  transmitter. While holding TRUNK button, press LOCK button and hold for  one second. Hold both buttons for a total of 3 seconds. Locks  cycle when programming is complete (if remote is not programmed  within 30 seconds after entering “99” override display, system will  default and you must begin again at step 2.)

4.  To  program second remote, pres FAN UP button until “PGM FOB2 502” is  displayed, then follow steps 2 and 3 to program second remote.

To exit  system, press RECIRC or RESET buttons.


Was This Information Useful?  Please take a moment to Like / Follow us and share via social media below. It is people like you that help spread the word about us.  It helps so much!  Thanks for visiting and sharing with your friends and family!