Here are the programming instructions for a 1995 Jaguar XJ Key Fob Remote. If you need an extra Key Fob or Replacement Fob for any vehicle you might have visit us at Keylessentryremotefob.com You can also leave comments or suggestions at the bottom of this blog and if you like what we provide please forward on to your friends & family; people like you are our best advertising tool!
1. Open boot lid (leave open)
2. Open driver's door (leave open)
3. Turn ignition switch ''ON'' but do not start engine.
4. Rock valet switch (located in center console) 5 times;
a single chirp and flash of the headlamps indicate the
Security Locking Control Module has entered the ''learning''
mode.
5. Press the alarm/lock (larger) button of the first transmitter.
This transmitter will be linked to position 1 of the
seat/steering/mirror memory. A tone will confirm that the
transmitter code was accepted. Note that the button must be
pushed within 15 seconds or the module will exit the ''learning''
mode.
6. Rock valet switch once. Two short chirps will indicate the
system is ready to accept a second transmitter.
Press the arm/lock (larger) button of the second transmitter.
Two tones will confirm the transmitter code was accepted.
7. Repeat steps 5 and 6 for up to a total of 5 transmitters.
The second transmitter programmed will be linked to position 2;
the third to position 3, and so forth. The number of
confirmation chirps mentioned in step 6 will indicate the
transmitter count (i.e. 3 chirps for third transmitter).
Note that you must cycle through steps 5 and 6 five times
regardless of the number of transmitters; if you have less
than 5 transmitters just repeat using the last transmitter
until 5 cycles have been finished.
8. Turn ignition off and close door and boot lid.
Test for proper operation of the seat/steering/mirror memories.
Having trouble programming the remote or just want a professional to program the remote for you? Enter your city or zip code in the search box below to find a professional key fob installer in your area.
ENTER YOUR CITY NAME OR ZIP CODE TO FIND A
PROFESSIONAL KEY FOB INSTALLER NEAR YOU
1. Open boot lid (leave open)
2. Open driver's door (leave open)
3. Turn ignition switch ''ON'' but do not start engine.
4. Rock valet switch (located in center console) 5 times;
a single chirp and flash of the headlamps indicate the
Security Locking Control Module has entered the ''learning''
mode.
5. Press the alarm/lock (larger) button of the first transmitter.
This transmitter will be linked to position 1 of the
seat/steering/mirror memory. A tone will confirm that the
transmitter code was accepted. Note that the button must be
pushed within 15 seconds or the module will exit the ''learning''
mode.
6. Rock valet switch once. Two short chirps will indicate the
system is ready to accept a second transmitter.
Press the arm/lock (larger) button of the second transmitter.
Two tones will confirm the transmitter code was accepted.
7. Repeat steps 5 and 6 for up to a total of 5 transmitters.
The second transmitter programmed will be linked to position 2;
the third to position 3, and so forth. The number of
confirmation chirps mentioned in step 6 will indicate the
transmitter count (i.e. 3 chirps for third transmitter).
Note that you must cycle through steps 5 and 6 five times
regardless of the number of transmitters; if you have less
than 5 transmitters just repeat using the last transmitter
until 5 cycles have been finished.
8. Turn ignition off and close door and boot lid.
Test for proper operation of the seat/steering/mirror memories.
Having trouble programming the remote or just want a professional to program the remote for you? Enter your city or zip code in the search box below to find a professional key fob installer in your area.
ENTER YOUR CITY NAME OR ZIP CODE TO FIND A
PROFESSIONAL KEY FOB INSTALLER NEAR YOU
Was This Information Useful? Please take a moment to help support this blog with a donation of any amount! Your donations help keep this site up to date. Thanks for visiting & Donating!
