Here are the programming instructions for a 2004 Volkswagen Passat Key Fob Remote. If you need an extra Key Fob or Replacement Fob for any vehicle you might have visit us at Keylessentryremotefob.com You can also leave comments or suggestions at the bottom of this blog and if you like what we provide please forward on to your friends & family; people like you are our best advertising tool!
ORDER THIS REMOTE PART HERE:
PLEASE NOTE: When you begin the programming sequence to sync your remote to your installed remote keyless entry (RKE) system, you MUST HAVE ALL OF YOUR REMOTES (Including PREVIOUSLY PROGRAMMED remote(s)) to be programmed with you at the time of programming…
ALL PREVIOUSLY PROGRAMMED REMOTES WILL BE ERASED AT THIS TIME.
(This is a safety feature which prevents anyone else from accessing your vehicle.)
UP TO 4 REMOTES (total) may be programmed to your vehicle’s system at one time.
KEYLESS REMOTE PROGRAMMING PROCEDURE:
AT TIME OF PROGRAMMING:
ALL remotes to be programmed and/or reprogrammed MUST BE PRESENT.
PROGRAMMING:
1. Switch ignition on with a key (don’t start the engine!); leave key in the ignition.
2. Mechanically lock vehicle at left front door, using second key.
3. On remote unit, press "Open" button once. A short horn signal will sound. NOTE:
The "Open" button is pressed once for programming the first, or a single remote unit.
When programming additional remote units for the second, third or fourth memory addresses, press the "Open" button two, three or four times, in one-second intervals.
Example: press the "Open" button once, wait 1 second, then press once again to program the second remote unit.
After 6 seconds, press "Open" button once to activate the coding process.
4. The remote unit will now be coded, and it can be used to unlock the central locking system. Switch ignition off.
The key must be removed from the ignition before the remote unit can be used to lock the vehicle. The coding process can be repeated up to 4 times for additional remote units. In between each remote unit coding, the ignition must be switched off.
Memory addresses, erasing.
It is possible to erase the memory, e.g. if the customer has lost a remote unit. Proceed as follows.
Switch ignition on with a key (don’t start the engine!); leave key in the ignition.
Mechanically lock vehicle at left front door, using second key.
On remote unit, press "Open" button 5 times in one-second intervals. A short horn signal will sound.
Then after 6 seconds, press "Open" button once to activate memory erasing process.
Memory is now erased, and the central locking system can no longer be operated by the remote unit.
Switch ignition off.
5. As many as 4 new remote units can now be coded.
Having trouble programming the remote or just want a professional to program the remote for you? Enter your city or zip code in the search box below to find a professional key fob installer in your area.
ENTER YOUR CITY NAME OR ZIP CODE TO FIND A
PROFESSIONAL KEY FOB INSTALLER NEAR YOU
ORDER THIS REMOTE PART HERE:
PLEASE NOTE: When you begin the programming sequence to sync your remote to your installed remote keyless entry (RKE) system, you MUST HAVE ALL OF YOUR REMOTES (Including PREVIOUSLY PROGRAMMED remote(s)) to be programmed with you at the time of programming…
ALL PREVIOUSLY PROGRAMMED REMOTES WILL BE ERASED AT THIS TIME.
(This is a safety feature which prevents anyone else from accessing your vehicle.)
UP TO 4 REMOTES (total) may be programmed to your vehicle’s system at one time.
KEYLESS REMOTE PROGRAMMING PROCEDURE:
AT TIME OF PROGRAMMING:
ALL remotes to be programmed and/or reprogrammed MUST BE PRESENT.
PROGRAMMING:
1. Switch ignition on with a key (don’t start the engine!); leave key in the ignition.
2. Mechanically lock vehicle at left front door, using second key.
3. On remote unit, press "Open" button once. A short horn signal will sound. NOTE:
The "Open" button is pressed once for programming the first, or a single remote unit.
When programming additional remote units for the second, third or fourth memory addresses, press the "Open" button two, three or four times, in one-second intervals.
Example: press the "Open" button once, wait 1 second, then press once again to program the second remote unit.
After 6 seconds, press "Open" button once to activate the coding process.
4. The remote unit will now be coded, and it can be used to unlock the central locking system. Switch ignition off.
The key must be removed from the ignition before the remote unit can be used to lock the vehicle. The coding process can be repeated up to 4 times for additional remote units. In between each remote unit coding, the ignition must be switched off.
Memory addresses, erasing.
It is possible to erase the memory, e.g. if the customer has lost a remote unit. Proceed as follows.
Switch ignition on with a key (don’t start the engine!); leave key in the ignition.
Mechanically lock vehicle at left front door, using second key.
On remote unit, press "Open" button 5 times in one-second intervals. A short horn signal will sound.
Then after 6 seconds, press "Open" button once to activate memory erasing process.
Memory is now erased, and the central locking system can no longer be operated by the remote unit.
Switch ignition off.
5. As many as 4 new remote units can now be coded.
Having trouble programming the remote or just want a professional to program the remote for you? Enter your city or zip code in the search box below to find a professional key fob installer in your area.
ENTER YOUR CITY NAME OR ZIP CODE TO FIND A
PROFESSIONAL KEY FOB INSTALLER NEAR YOU
Was This Information Useful? Please take a moment to help support this blog with a donation of any amount! Your donations help keep this site up to date. Thanks for visiting & Donating!
