Here are the programming instructions for a 2007 GMC Sierra Key Fob Remote. If you need an extra Key Fob or Replacement Fob for any vehicle you might have visit us at Keylessentryremotefob.com You can also leave comments or suggestions at the bottom of this blog and if you like what we provide please forward on to your friends & family; people like you are our best advertising tool!
ORDER THIS PART NUMBER HERE: 21997127
2007 Old Body Style
1. Close all vehicle doors.
2. Insert the key into the ignition.
3. Hold down the power UNLOCK button on the driver’s door panel-continue to hold down until instructed to release in step 9.
4. Perform steps 5 through 8 in fairly rapid succession.
5. Turn the ignition switch to the ON position (as far as you can go without starting the engine).
6. Turn the ignition switch to the OFF position.
7. Turn the ignition switch to the ON position.
8. Turn the ignition switch to the OFF position.
9. Release the power unlock button on the door panel. The vehicle will lock and unlock the doors automatically.
10. Hold down the LOCK and UNLOCK buttons on the transmitter simultaneously until the door locks and unlocks. This step may take up to 30 seconds.
11. Repeat step 10 NOW for each additional transmitter (including any existing transmitters).
12. Turn the ignition switch to the ON position in order to exit the transmitter programming mode.
2007 New Body Style
Use this Procedure for Vehicles with Driver Information Center Buttons
This information is in your Owners Manual in the Drivers Information Center Section.
1. Insert Key and turn to ON position so you can access Driver Information Center
2. Press the vehicle information button until PRESS TO RELEARN REMOTE KEY displays
3. Press the set/reset button until REMOTE KEY LEARNING ACTIVE displays
4. Press and hold the lock and unlock buttons on the keyless remote at the same time for approximately 15 seconds. A chime will sound indicating that the remote is programmed.
5. To program additional remotes at this time repeat step 4. This vehicle can have a maximum of eight remotes programmed
6. To exit programming mode turn key off and remove key. Test remote(s).
Use this Procedure for Vehicles without Drivers Information Center Buttons
To access this display, the vehicle must be in Park (P) with key in the on position (as far as you can go without cranking engine)
1. Press the trip odometer reset stem until RELEARN REMOTE KEY displays.
2. Press and hold the trip odometer reset stem for three seconds. The message REMOTE KEY LEARNING ACTIVE will display
3. Press and hold the lock and unlock buttons on the first keyless remote at the same time for approximately 15 seconds. A chime will sound indicating that the remote is programmed.
4. To program additional remotes at this time repeat step 3. This vehicle can have a maximum of eight remotes programmed.
5. To exit programming mode turn key off and remove key. Test remote(s).
Having trouble programming the remote or just want a professional to program the remote for you? Enter your city or zip code in the search box below to find a professional key fob installer in your area.
There is no onboard programming procedure for this vehicle. This vehicle requires special equipment be connected to the vehicle to program the keyless remote.
Try a locksmith before the dealership, they are usually 50% the cost. To find a preferred locksmith in your area use our recommended locksmith locator on our website below:
Enter Your City In The Search Box
Enter Your City In The Search Box
Here is some good advise from a customer of ours. If you have to go to a dealer to have your keyless entry remote key fob programmed by a dealership, here is a way to try to get them to do it for free:
Take ur vin number down and call the local dealer, or better yet take it down to the dealer in person, and ask them if there has been a recall on ur vin - also mention u would like to get that key fob set up - he might do it free - just go by and be friendly during the day time - when he has time and inclination to help you - remember all workers at the dealer are sales men as with no sales - no job for any of them
This might or might not work, but it definitely can't hurt to try. You will be surprised how being nice to the service department can get you!
By Keyless Entry Remote Inc
