Keyless Entry Remote
close
close
Limited Time Offer! 15% Off Any 2 or More Key Fobs

2002 Dodge Durango Key Fob Remote Programming Instructions

Posted by Keyless Entry Remote on Apr 16th 2015

Here are the programming instructions for a 2002 Dodge Durango Key Fob Remote. If you need an extra Key Fob or Replacement Fob for any vehicle you might have visit us at Keylessentryremotefob.com You can also leave comments or suggestions at the bottom of this blog. If you like what we provide please forward on to your friends & family and share via the social media icons below; people like you are our best advertising tool!

ORDER THIS KEY FOB PART NUMBER HERE: 04686481AC





Programming Instructions:
YOU MUST HAVE A WORKING REMOTE FOR THIS PROCEDURE TO WORK. IF YOU DON'T HAVE A WORKING REMOTE THEN YOU MUST HAVE A REMOTE PROGRAMMED BY A DEALER OR LOCKSMITH USING DIAGNOSTIC EQUIPMENT.

PLEASE READ ENTIRE PROCEDURE BEFORE PERFORMING. SOME VEHICLES MAY USE ONE OF TWO PROCEDURES. IF PROCEDURE 1. DOES NOT WORK THEN PLEASE USE PROCEDURE 2.



Programming procedure #1.

Obtain all remote transmitters for this vehicle.

1. Put key in ignition and turn ignition switch to ON position (as far as you can turn key without cranking engine).

2. Press and hold UNLOCK on a currently functioning remote for 4 to 10 seconds.

3. While holding the UNLOCK button during the 4 to 10 second period, press the panic button for one second and release both buttons at the same time. A chime should sound within three seconds to indicate the vehicle has entered programming mode.

4. Press any button on the remote used in step 3. You should hear an audible tone indicating that remote has been re-programmed. This step must be done within 30 seconds of hearing first chime in step 3.

5. Within 30 seconds of completiong step 4. press any button on the next remote. Repeat step 5. for all additional remotes including working remotes.

6. Programming is now complete. Turn ignition off and test remotes to ensure proper programming.

Programming Procedure #2

Obtain all remote transmitters for this vehicle.

1. Put key in ignition and turn ignition switch to ON position (as far as you can turn key without cranking engine).

2. Press and hold UNLOCK on a currently functioning remote for 4 to 10 seconds.

3. While holding the UNLOCK button during the 4 to 10 second period, press the panic button for one second and release both buttons at the same time. A chime should sound within three seconds to indicate the vehicle has entered programming mode.

4. Press the LOCK and UNLOCK buttons simultaneously on the same remote used in step 3. then release. You should hear an audible tone indicating that the remote was recognized. Once tone is heard press and release the UNLOCK button on that remote. A chime should sound indicating that the remote has been programmed. This must be done within 30 seconds of step 3.

5. Within 30 seconds of completing step 4. press the LOCK and UNLOCK button on the next remote then release. You should hear an audible tone indicating that the remote was recognized. Once tone is heard press and release the UNLOCK button on that remote. A chime should sound indicating that the remote has been programmed. Repeat step 5. for all additional remotes including working remotes.

6. Programming is now complete. Turn ignition off and test remotes to ensure proper programming.

Transponder Key Programming Instructions: 


Obtain all keys for this vehicle.

You must have two working programmed keys to do this procedure.

1. Insert first programmed key into ignition and turn ignition switch to ON for 3 to 15 seconds. Do not exceed 15 seconds.

2. Turn ignition switch to OFF and remove key.

3. Insert second programmed key into ignition and turn ignition switch to ON. You must do this within 15 seconds of removing first key. After 10 seconds the immobilizer warning lamp will illuminate and an audible tone will be heard.

4. Turn ignition switch to OFF and remove key.

5. Within 60 seconds insert new unprogrammed key into ignition and turn ignition switch to ON.

6. After 10 seconds an audible tone will be heard and the immobilizer warning lamp will illuminate for 3 seconds.

7. Turn ignition switch to OFF and remove key.

8. For each additional key to be programmed you must start at step 1 and follow procedure again.

You can have up to 8 keys programmed to vehicle.
Having trouble programming the remote or just want a professional to program the remote for you? Enter your city or zip code in the search box below to find a professional key fob installer in your area.

ENTER YOUR CITY NAME TO FIND A
PROFESSIONAL KEY FOB INSTALLER NEAR YOU
By Keyless Entry Remote Inc

We Are The Experts

Unmatched, expert support for ANY keyless remote issue. We've got your back!

Need Help?

Stay In The Know

Sign up for Keyless Entry Remote's News, Sales, and Deals.

Join Our Mailing List

Programming Instructions

Remote & Transponder Key Programming Instructions for over 5,000 vehicles!

Find Yours