Here are the programming instructions for a 2006 Dodge Charger Key Fob Remote. If you need an extra Key Fob or Replacement Fob for any vehicle you might have visit us at Keylessentryremotefob.com You can also leave comments or suggestions at the bottom of this blog. If you like what we provide please forward on to your friends & family and share via the social media icons below; people like you are our best advertising tool!
ORDER THIS KEY FOB PART NUMBER HERE: 56038757AH, 56040652AC, 56040652AD, 56038768AD, 56038757AE, 56038768AG, 56038749AG. 05179512AA
Programming Instructions:
FOR REMOTE PART (LOCK, UNLOCK, PANIC, TRUNK)
PLEASE NOTE: YOU MUST HAVE ONE WORKING REMOTE TO ADD ONE MORE TO THE SYSTEM. IF YOU DO NOT HAVE ONE WORKING REMOTE RIGHT NOW THEN THESE INSTRUCTIONS WILL NOT WORK. YOU WILL HAVE TO GET IT PROGRAMMED BY A LOCKSMITH, MECHANIC, OR DEALER.
1. Press LOCK button 5 times at 2 second intervals to resynchronize remote.
2. Insert key into the ignition switch. Turn ignition to the RUN position
(as far as you can go without cranking engine). Wait for ignition chimes
to stop.
3. Using the working remote, press and hold the UNLOCK button on the remote
for 4 to 10 seconds.
4. Within the specified 4 to 10 seconds, continue pressing the UNLOCK button
and then press the PANIC button ( on the programmed remote ) for 1 second
and release both buttons. A chime will sound to indicate that the remote
programming mode has been entered ( allow 3 seconds for chime to sound ).
5. Within 30 seconds of the chime, press and release the LOCK and UNLOCK
buttons simultaneously then press and release just the UNLOCK button
on the same remote. A chime will sound indicating the remote has been
programmed. Press and release the LOCK and UNLOCK buttons simultaneously
and then press the UNLOCK button on each new remote you wish to program
at this time. A chime will sound after each additional remote is programmed.
6. Turn the ignition OFF and remove key.
7. Test Remotes.
FOR KEY TRANSPONDER/IMMOBILIZER CHIP (METAL KEY)
PLEASE NOTE: THIS PROCEDURE CAN ONLY BE USED ON VEHICLES BUILT IN USA. YOU MUST HAVE TWO WORKING PROGRAMMED REMOTE/KEYS BEFORE YOU CAN ADD A THIRD REMOTE/KEY. IF YOU ONLY HAVE ONE WORKING REMOTE/KEY AND WANT TO ADD A SECOND KEY THIS PROCEDURE WILL NOT WORK AND YOU WILL HAVE TO GET IT PROGRAMMED BY A LOCKSMITH, MECHANIC, OR DEALER.
1. Using first programmed remote/key turn ignition to the ON position
for 5 seconds. (Do not crank engine). Turn remote/key off and remove.
2. Within 5 seconds insert second working programmed remote/key.
Turn ignition to the ON position (Do not crank engine) security light
will begin to flash and chime will be heard within 10 seconds. Turn
remote/key off and remove. NOTE: Some vehicles will not chime,
only the security light will flash.
3. Within 5 seconds insert third NEW CUT remote/key and turn ignition to
the ON position (Do not crank engine). The security light should start
flashing and within 10 seconds you should hear a chime and the
security light should go out. Once the security light goes out, the new
remote/key should be programmed. Turn remote/key to the OFF
position, remove key.
4. Test key and remote.
Having trouble programming the remote or just want a professional to program the remote for you? Enter your city or zip code in the search box below to find a professional key fob installer in your area.
ENTER YOUR CITY NAME TO FIND A
PROFESSIONAL KEY FOB INSTALLER NEAR YOU
ORDER THIS KEY FOB PART NUMBER HERE: 56038757AH, 56040652AC, 56040652AD, 56038768AD, 56038757AE, 56038768AG, 56038749AG. 05179512AA
Programming Instructions:
FOR REMOTE PART (LOCK, UNLOCK, PANIC, TRUNK)
PLEASE NOTE: YOU MUST HAVE ONE WORKING REMOTE TO ADD ONE MORE TO THE SYSTEM. IF YOU DO NOT HAVE ONE WORKING REMOTE RIGHT NOW THEN THESE INSTRUCTIONS WILL NOT WORK. YOU WILL HAVE TO GET IT PROGRAMMED BY A LOCKSMITH, MECHANIC, OR DEALER.
1. Press LOCK button 5 times at 2 second intervals to resynchronize remote.
2. Insert key into the ignition switch. Turn ignition to the RUN position
(as far as you can go without cranking engine). Wait for ignition chimes
to stop.
3. Using the working remote, press and hold the UNLOCK button on the remote
for 4 to 10 seconds.
4. Within the specified 4 to 10 seconds, continue pressing the UNLOCK button
and then press the PANIC button ( on the programmed remote ) for 1 second
and release both buttons. A chime will sound to indicate that the remote
programming mode has been entered ( allow 3 seconds for chime to sound ).
5. Within 30 seconds of the chime, press and release the LOCK and UNLOCK
buttons simultaneously then press and release just the UNLOCK button
on the same remote. A chime will sound indicating the remote has been
programmed. Press and release the LOCK and UNLOCK buttons simultaneously
and then press the UNLOCK button on each new remote you wish to program
at this time. A chime will sound after each additional remote is programmed.
6. Turn the ignition OFF and remove key.
7. Test Remotes.
FOR KEY TRANSPONDER/IMMOBILIZER CHIP (METAL KEY)
PLEASE NOTE: THIS PROCEDURE CAN ONLY BE USED ON VEHICLES BUILT IN USA. YOU MUST HAVE TWO WORKING PROGRAMMED REMOTE/KEYS BEFORE YOU CAN ADD A THIRD REMOTE/KEY. IF YOU ONLY HAVE ONE WORKING REMOTE/KEY AND WANT TO ADD A SECOND KEY THIS PROCEDURE WILL NOT WORK AND YOU WILL HAVE TO GET IT PROGRAMMED BY A LOCKSMITH, MECHANIC, OR DEALER.
1. Using first programmed remote/key turn ignition to the ON position
for 5 seconds. (Do not crank engine). Turn remote/key off and remove.
2. Within 5 seconds insert second working programmed remote/key.
Turn ignition to the ON position (Do not crank engine) security light
will begin to flash and chime will be heard within 10 seconds. Turn
remote/key off and remove. NOTE: Some vehicles will not chime,
only the security light will flash.
3. Within 5 seconds insert third NEW CUT remote/key and turn ignition to
the ON position (Do not crank engine). The security light should start
flashing and within 10 seconds you should hear a chime and the
security light should go out. Once the security light goes out, the new
remote/key should be programmed. Turn remote/key to the OFF
position, remove key.
4. Test key and remote.
Having trouble programming the remote or just want a professional to program the remote for you? Enter your city or zip code in the search box below to find a professional key fob installer in your area.
ENTER YOUR CITY NAME TO FIND A
PROFESSIONAL KEY FOB INSTALLER NEAR YOU
By Keyless Entry Remote Inc
